Hispasat problem

[Roly62]

Hi:
I have a pansat 2800 with dish 500 working on dn, and a dish of 30 inchs with a linear lnb for hispasat. my settings are lnb standart, freq: 10750, diseq 4, tp 12052V27.500.
So my problem is that i had siignal before change the last bin and now im not have Q, just 72 level even with the cable desconected, and no Q.

Please help me

[jjk326]

Your settings say, disqc port 4 , then you have a switch, check it to see if it is bad. No Q means signal does not arrive to lnb because dish have move , or signal does not pass the switch. or settings wrong,

[DJ COOKIE]

Originally Posted by Roly62

Hi:
I have a pansat 2800 with dish 500 working on dn, and a dish of 30 inchs with a linear lnb for hispasat. my settings are lnb standart, freq: 10750, diseq 4, tp 12052V27.500.
So my problem is that i had siignal before change the last bin and now im not have Q, just 72 level even with the cable desconected, and no Q.

Please help me

the tp you should set is 11884 it's the trick to catching hispasat

[Roly62]

Originally Posted by DJ COOKIE

the tp you should set is 11884 it's the trick to catching hispasat

yes , thats ok but i put the coax direct to the receiver and nothing with Q, need the settings please.
LNB Universal
Dish 30"
Pansat 2800
Azimut 124
Alt: 27.5

[woodcreeker]

To see Quality on some satellites you need to change the TP number.

Change the TP to 11884 like DJ COOKIE said above to see Quality on Hispasat.

Just like to see Quality on 119W you need to change the TP to 12239.

You can only temporarily change these TP settings to see signal, you cannot save them. Do not let this frustrate you, and you know from this that you have your dish aimed properly. Once you have the settings right, simply Exit, Save and go blind scan the Hispasat satellite.

[Manuelsoto]

Originally Posted by woodcreeker

To see Quality on some satellites you need to change the TP number.

Change the TP to 11884 like DJ COOKIE said above to see Quality on Hispasat.

Just like to see Quality on 119W you need to change the TP to 12239.

You can only temporarily change these TP settings to see signal, you cannot save them. Do not let this frustrate you, and you know from this that you have your dish aimed properly. Once you have the settings right, simply Exit, Save and go blind scan the Hispasat satellite.

Hello everyone.
I'm writing because at this present moment I am attempting to install another dish so that I may recieve signal from Hispasat 30W. Are there any suggestion as to the type of dish that I may get away with. At the present time im trying to use an old DTV sat with a singal lnb.
ELevation :25.2
Az: 124.1 true, 137.3 using compass
Skew: -38.9
Diseq: 3
What would be the proper TP. Hey and thanks again for the hookup on my 1000.

[DJ COOKIE]

Originally Posted by Manuelsoto

Hello everyone.
I'm writing because at this present moment I am attempting to install another dish so that I may recieve signal from Hispasat 30W. Are there any suggestion as to the type of dish that I may get away with. At the present time im trying to use an old DTV sat with a singal lnb.
ELevation :25.2
Az: 124.1 true, 137.3 using compass
Skew: -38.9
Diseq: 3
What would be the proper TP. Hey and thanks again for the hookup on my 1000.

you need a linear lnb of 10750 to catch this bird and im not shure but i think you would need a 1.0 meter dish that far up north

[Manuelsoto]

Originally Posted by DJ COOKIE

you need a linear lnb of 10750 to catch this bird and im not shure but i think you would need a 1.0 meter dish that far up north

what if I started off first with replacing the lnb.

[DJ COOKIE]

yes that would help .. lol.. then go for the bigger dish