[phydoe]

can some one plz help. I just converted my flu b75 to puff.looks like i did OK per instructions.I loaded haddad_V203_PUFF_F_EMU.bin after i gets done downloading the file i get a message -75- and then the word on in the display when I turn off the box it goes back to displaying p u f f over and over.what am i doing wrong? plz help...Is it because i did not save my channel list?

[boboisno1]

It sounds like it should be good, best thing with puff conversions is once you do an autoscan you no longer need to load a channel list anymore, the channels get saved automatically. You could load an old channel list no but to be honest with all the channel movements channel lists are not the best thing to use anymore. So setup your antenna settings then do an autoscan and when your done you may have to hit 8282 on the remote and "set default key", I'm not sure if setting default key is a requirement anymore bu if the channels won't come in after the scan try it.

[phydoe]

dear mister moderator so is it ok that it just says puff over and over?how do i know if I'm done and if the bin file i load was ok,is it even the correct bin file.when is the box going to say on..thx for your quick replies to my questions.

[jjk326]

Originally Posted by phydoe

can some one plz help. I just converted my flu b75 to puff.looks like i did OK per instructions.I loaded haddad_V203_PUFF_F_EMU.bin after i gets done downloading the file i get a message -75- and then the word on in the display when I turn off the box it goes back to displaying p u f f over and over.what am i doing wrong? plz help...Is it because i did not save my channel list?

display puff all over because loaded wrong bin, load last puff bin(fwank v203-v2) fact reset, sat setting and sat scan. see in archive for these bin. load bin when see first p.

[boboisno1]

haddad_V203_PUFF_F_EMU and fwank v203-v2 are both versions of puff bins.

[phydoe]

sorry i took so long but i was trying to get the system to run.gentlemen good news it accepted the (fwank v203-v2) bin file and it looks like we moved forward..BUT I search for sat 82 because that is what came up AND got bad or scrambled channel,normally i have 119 and 110 when i was ruining b75 bins.can plz continue HELPING ME.thx

[phydoe]

im stuck can someone help me

[woodcreeker]

What you have to do is setup a satellite and then blind scan channels. Reboot receiver from the rear power switch after each blind scan, as there is a problem with the new Full EMU bin compressions.

I can help with settings, but I do not know your dish antennas and LNBs.

Try this...

Echo 7/Ku (119W)
LNB Type: Dish-Pro
LNB Freq: 11250
DiSEqC: (1.0) #1
TP: [2] 12239 V 20.000

Echo 8.10/Ku (110W)
LNB Type: Dish-Pro
LNB Freq: 11250
DiSEqC: (1.0) #2
TP: [2] 12239 V 20.000

The above settings are for a Dish 500 w/ a DP LNB. If you have seperate LNBs on 2 18" dishes, you may have to check and know which way they are connected into the DiSEqC switch. It is best to wire 119W into port 1 and 110W into port 2 on the DiSEqC switch so you are on the same page as everyone else.

Good Luck !!

[phydoe]

woodcreeker thx I will try this when I get home later to day.but i think this will work.thx again.

[phydoe]

I want to start of by saying thank you to BOBOISNO1,JJK326,WOODCREEKER for all the support I was given.GREAT SITE,GREAT HELP,GREAT MEMBERS,hope to some day help someone in need on this site...system up and running...

[boboisno1]

Glad to hear you're up and running and thanks for the update!