[woodcreeker]

What type of a Dish is it ??

It is a small 18" single eyed dish or a Dish 500 with a Twin LNB ??

[fxnaughty]

its a single lnb and i guess its an 18 inch

[fxnaughty]

I still need help here

[woodcreeker]

Sorry, you haven't posted in awhile, so I waited for a reply.

Which satellite was it working on ??

Like, were there a lot of Vu channels for instance, or Vue channels ??

Give me an example of some of the channels you were watching. Seems to me you were watching BEV. You may have to realign the dish to one of the Echo satellites. Answer the question, I will give you some directions to get you back up with something.

[fxnaughty]

I had a lot of vu channel
the only thing I really havn't done and probably could be is the boot v6 file I never did load the boot file..

this is how I set it up the last time i set my install then to antena setup and scroll down to see what satellite gets quality signal..thats when I selected echo 7 and 8 and it was working with bin 411 for a while untill 301 and 302 came out :-(

[woodcreeker]

Okay, your problem is the dish is aligned to Nimiq 1. That is why it stopped working. What you have to do is align it for Echo 7 119W.

Do a Factory Reset first.
Go to Menu -> Factory Setting -> 0000 (4 zeros) -> Ok

Drop your dish about 8 elevations, and move the dish towards the West about 30 degrees to find signal again.

So go into the settings, and change...

Echo 7/Ku
LNB Type: Standard
LNB Freq: 11250
TP: [2] 12239 V 20.000 <-- One arrow to the right

Remember when you are going into this menu for Echo 7/Ku to check or find signal, the TP number has to be on [2] 12239 20.000.

You can Exit and Ok to Save.

Once you find signal like I suggested above, go to Blind Scan and scan Echo 7/Ku.

Your dish is pointed to Nimiq 1 91W.

The best way to test DN is to get another 18" dish like the one you have. There are 2 DN satellites, 110W and 119W.

Hope This Helps !!

[fxnaughty]

when I go to antenna setup i get signal on echo 7
LNB Type: Standard
LNB Freq: 11250
but with TP: [1] i get full singal when change to TP: [2] I get no signal

just want to make sure its the satellite need adjustment and nothing else cause its like freezing out there man :-)...
just making sure and did i mention i never loaded the boot v6 file

[fxnaughty]

even thought i get no link quallity with echo 7 at tp 2 i did a regular scan and blind scan and found alot of channel but it shows nothing y is that?

[fxnaughty]

did you forgot about me again

[Rollouts]

Originally Posted by fxnaughty

even thought i get no link quallity with echo 7 at tp 2 i did a regular scan and blind scan and found alot of channel but it shows nothing y is that?

In my opinion of your situation I would have to say that one of the following is true

#1 you do not have the latest bin file for your receiver loaded

#2 your dish is just barley out of adjustment

just to be sure go download the latest bin file in the file downloads section of the main forum

good luck

[fxnaughty]

i unload the new bin 303 the same day it came out
but y is it on tp 1 i get like 99% quality and when i set the tp 2 i get none

[woodcreeker]

I didn't forget you. I told you that you need to move your dish. Right now you are aimed at Nimiq 1. What more would you like me to say on this ?? Read Post #26 above.

[fxnaughty]

well i was telling you the rest of my story hoping to give you more insight on the scenario

[aerosol]

well i am getting no picture here either and I just downloaded latest bin file as well. it will display the channel and even programming info but no picture.

[fxnaughty]

I got the same problem and when i re alignment the dish i cant get anthing on tp 2